Peugeot 3008 Key Fob Problems
The mid-sized SUV from Peugeot 3008, has lots of positive points. It looks smart, drives well and comes with a big boot. But can it fend against strong competition in the most crowded area of the market?
If your Peugeot key fob isn't functioning, it might have been exposed to clean tap water or soapy water. It may be necessary to remove the battery and clean it with electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs are powered by a coin-sized battery. This power is used to operate the remote locking system, as well as other functions. This battery has a limited lifespan and is susceptible to be worn out after a long period of usage. An easy way to determine whether the battery is defective is by performing an electrical test. Multimeters are used to measure the voltage between the plus and minus poles of the battery. This test will determine whether the battery is dead.
The receiver module may be the reason behind your key fobs failing to function after having used your Peugeot 3008 for a long time. The receiver module is responsible for receiving radio frequency signals from key fobs and sending them to the vehicle's systems. If the receiver module is in problems, it won't be able to transmit commands to other modules in the car.
Another common reason for a non-working key fob is moisture or sweat in the circuit board. This can lead to short circuits that drain the battery and stop the remote locking feature of the fob. If this is the case then you must take your key fob to an expert in chip level repair to repair it.
Water damage
If you dropped your key fob into the pool, tossed it in the washer or left it in the rain for too long, water damage can be a major issue. Water makes for a good conductor and can easily short out parts of the circuit board. It can also cause corrosion to the metal traces as well as other components of the key fob. A wet circuit can cause the battery to lose its charge.
If you have an extra key fob try using it to lock/unlock your Peugeot 3008 to eliminate the possibility that a dead coin battery is the cause of the problem. Interference signals can cause your key fob not to function properly. These interfere with the signal sent by the receiver module. These signals could come from a wide range of things such as radio transmitters in close proximity.
If you hear sloshing sounds emanating from your Peugeot 3008 while driving it could be due to a blocked condensate drain of the evaporator. You can determine this by locating the drain holes underneath your door and blowing compressed air through them. You can also use flexible metal wire to wiggle drain holes to get rid of any dirt collected. The sound of sloshing can also indicate that there are air pockets within the coolant system.
A malfunctioning receiver module
The receiver module of a Peugeot 3008 key fob is responsible for sending the remote keyless system signal from the key fob to the car's receiver. If this module is damaged, it can stop the car from recognizing the key fob. Other reasons that could cause this issue are dead batteries water damage or interference with electronic devices that operate at the same frequency as the key fob. In these situations the car might display the message "card not detected" on the display.
There are many options to resolve this problem. Try replacing G28 or reprogram the key fob. You can also start your vehicle with a spare key. If the key fob isn't working after all these steps, it might be due to a malfunctioning chip.
It is best to take out the chip and clean it with paper towels and rubbing alcohol. If the chip has been damaged, you should purchase an entirely new one. The FB Series enclosures come with the battery holder for coins that fits the most popular types of key fob batteries. They can also be customized with digital printing and CNC machined cutouts. If your key fob was exposed to dirty or salted tap water, it's possible that the chip has become contaminated.
Faulty keyless entry system
If you get the message "card not detected" this signifies that your car can't receive the signal from your key fob. This can be due to a variety of causes including the battery being weak or dead. The problem can often be solved by pressing the start button on the key fob. In some cases you may require taking the keyfob to a Peugeot dealer for repairs.
The battery test is the first step to diagnosing the problem with a Peugeot 3008 keyfob, which is unable to unlock or lock doors. Batteries are often the main cause of a malfunctioning fob however there are a variety of other causes that can cause this issue too. These include worn buttons as well as water damage.
If you've recently been exposed to water and have your Peugeot key fob exposed to pure tap water it's best to remove the battery and dry the electronic components using paper towel. You could also try using isopropyl ethanol or cleaning solution to do this. If the fob has been exposed to salt or soapy water, it's recommended to replace it.
If your key fob still doesn't work, you can reset it by removing the battery of 12 volts for 15 minutes. Connect the negative cable first, then the positive cable.